AC Cbb60 Water Pump Water Pump Motor Capacitor Manufacturers

CBB60 Water Pump Motor Capacitors From Our Cixi Factory

CIXI RIYI CAPACITOR FACTORY manufactures the AC Cbb60 Water Pump Water Pump Motor Capacitor Manufacturers group inside our CBB60 plastic case range. These are epoxy-sealed metallized polypropylene run capacitors for single-phase pump motors: domestic boosters, garden and jet pumps, submersible and transfer pumps, and circulation pumps used in appliances. We build them at 10, 12, 15, 20, 30 and 45 µF, mainly 450 V S0, with insert terminal, lead wire, sheathed wire and UL1015 wiring options.

A pump motor leaves its capacitor in circuit for the whole run cycle, so the winding sees continuous AC stress plus start inrush. Our fully sealed case and self-healing film construction are specified for that duty, and oil-resistant versions cover pumps where lubricant or fluid contact is possible.

Our Water Pump Motor Capacitor Range

Every model below is part of the CBB60 plastic case capacitor family, using the same sealed body and metallized film winding, differing in capacitance, voltage class and termination.

Capacitance Steps We Build for Pump Motors

Standard values available in the water pump motor capacitor group, shown on a microfarad scale.

Reading the Marking on a Pump Capacitor

• Capacitance (µF) sets the phase shift and running torque. Undersized values lose starting torque; oversized values raise winding current and heat.
• Voltage rating is the continuous AC working voltage. The group is predominantly 450 V, with 250 V, 300 V and 500 V values elsewhere in the aluminum case CBB60 capacitors range for circuits with different margins.
• S0 or S3 class describes the duty and protection level of the housing. S3 models are built as explosion-proof construction with a controlled case rupture behaviour.
• Termination code (C, B, lead colour, UL1015) tells you how the part lands in the pump terminal box.

Voltage Ratings Available Across the Range

450 V S0 is the standard working point for water pump motors; higher ratings are used where the mains or the motor insulation calls for additional margin.

Applications We Match to Each Build

Construction, Quality Control and Acceptance

We run 11 automatic slitting machines and 15 imported automatic winding machines, with in-house sealing and finishing, so capacitance consistency and case integrity are controlled on our own lines rather than outsourced. Finished parts pass low-loss and high insulation resistance checks for the group, alongside self-healing and overvoltage performance verification.

• ISO 9001 quality management and ISO 14001 environmental management systems.
• Product certificates held across the range include CQC, TUV, VDE, IMQ, UL and CE.
• Routine inspection covers capacitance value, dissipation factor, insulation resistance and withstand voltage before packing.
• Batch records and certificate references travel with the shipment so incoming inspection can be closed out against the agreed drawing.

Information We Use to Configure Your Solution

A pump capacitor is selected against the motor and the harness, not against a catalogue number alone. Send the following and we will return a matched configuration and quotation.

• Pump type, motor rating and operating voltage, plus the value and rating on the existing capacitor.
• Required termination: 1+1 or 2+2 terminal, lead colour, lead length, sheathed wire or UL1015 wire.
• Ambient conditions, including moisture, oil exposure and whether the pump body is sealed.
• Case envelope limits if the mounting bracket or terminal cover restricts the body size.
• Order volume, packing format and any incoming-inspection requirements, such as a test report per batch.

FAQs From Pump and Appliance Manufacturers

Which water pump motor capacitor values do you hold in series production?

The water pump group is built at 10, 12, 15, 20, 30 and 45 µF, predominantly 450 V S0, plus a 10 µF 450 V S3 explosion-proof version. Oil-resistant 12 µF and 30 µF builds cover lubricant-exposed pumps. Other CBB60 values are available through the wider range for pump motors that sit outside these steps.

Can you supply a replacement that matches an existing pump capacitor?

Yes. We match capacitance, voltage rating and class first, then reproduce the connection style so the part drops into the existing terminal box. Send the original marking, a photo of the lead arrangement or a physical sample and we confirm the equivalent build before production.

Do you develop custom terminal, lead and case configurations?

We develop custom models from customer drawings or samples. Typical adaptations are lead length and colour, terminal pitch, sheathed sleeving, UL1015 wire and dual-value sections for motors with a separate auxiliary winding. Our engineering staff review the drawing before winding specifications are released.

Which standards and certificates apply to these capacitors?

Our systems are certified to ISO 9001 and ISO 14001, and products hold CQC, TUV, VDE, IMQ, UL and CE certificates. We state the applicable certificate for the specific model on the quotation so it aligns with your approval file.

How does the pump capacitor relate to your other product families?

Pump motors, circulation fans and appliance drives share the same physical needs, so the same body and winding knowledge carries into the electric motors capacitor group and the CBB65 explosion-proof range for heavier single-phase and dual-run duties.

What are your production capacity and shipping arrangements?

Daily output reaches 60,000 capacitors from our 25,000 m² plant in Cixi, Zhejiang. We ship mainly by sea from Ningbo, with air freight available when a schedule is tight, and our products are exported to markets including the United States, Indonesia, the Philippines, Turkey and Egypt.